Plus M-5 Uživatelská příručka Strana 1

Document #120523 Rev-A Fastmark M5 Plus Series Direct Thermal Barcode Printer User’s Guide

8 8. Gently push the peel-off panel to lock onto the lower inner cover. 9. Reassemble parts in reverse procedures after installing the module. Pee

9Peel-Off Panel 3.4 Loading Labels for Peel-off Mode (Option) 1. Open the peel-off module by pulling it forward. Fig. 9 Open the peel-off panel 2.

106. Close the top cover. Fig. 11 Label loaded completely in peel-off mode 3.5 External Media Roll Mount Installation (Option) 1. Attach an ex

11 3. Feed the media (printing side face up) into the external opening located at the rear of the printer and then through the media guides. Fig. 1

123.6 Cutter Module Installation (Option) 1. Pull the top cover levers to open the top cover. 2. Remove the front panel from the lower cover. Pull

136. Remove the screw from the memory card cover, and left the cover off. 7. Plug in the Cutter Driver IC at U14(M5 DT) / U30(M5 DT PLUS) socket o

148. Hold the lower cover and lift up the lower inner cover. 9. Thread the cutter module cable through the bezel. 10. Connect the cutter module cab

153.7 Loading Media in Cutter Mode 1. Open the printer top cover. 2. Insert the spindle into the media roll. 3. Install a media roll onto the rol

163.8 Internal Ethernet Print Server Module Installation (Option) 1. Break through the plastic partially connected at the rear side of lower cove

173. Fasten the RJ45 connector daughter board on the plastic and metal standoff. The ground wire from the mechanism must be screwed on the daughter b

i 1. Introduction...1 2. Getting Started...

185. Remove the 2 screws from the motor bracket and 1 screw in the lower inner cover to install the internal print server. Screw Screws

19 7. Plug the RJ45 white connector to the RJ45 daughter board connector. 8. Plug the print server module interface cable to connector J1A and

203.9 Diagnostic Tool The Diagnostic Utility is a tool that allows users to explore the printer's settings and status; change printer settings;

213.9.2 Printer Function (Calibrate, Ethernet setup, RTC setup…) 1. Select the PC interface connected with bar code printer. 2. Click the “Function”

22 3. Plug in the memory card on main board. M5 DT Model (Option) M5 DT PLUS Model (SD card) 4. Reinstall the memory card cover. * Recommended SD

234. Power on Utilities There are six power-on utilities to set up and test printer hardware. These utilities are activated by pressing FEED button

24 4.2 Gap/Black Mark Calibration, Self-test, Dump Mode While calibrate the gap/black mark sensor, printer will measure the label length, print the

25Self-test Printer will print the printer configuration after gap/black mark sensor calibration. Self-test printout can be used to check if there i

26Dump mode Printer will enter dump mode after printing printer configuration. In the dump mode, all characters will be printed in 2 columns as follo

274.3 Printer Initialization Printer initialization is used to clear DRAM and restore printer settings to defaults. The only one exception is ribbon

11. Introduction Thank you for purchasing the AMT Datasouth M5 DT PLUS Direct Thermal Bar Code Printer. Although the printer takes only a small amoun

284.4 Black Mark Sensor Calibration Set black mark sensor as media sensor and calibrate the black mark sensor. Please follow the steps as below. 1. T

295. Maintenance 5.1 Cleaning This session presents the clean tools and methods to maintain your printer. 1. Please use one of following material

30Bar ethanol to wipe it. Sensor Compressed air or vacuum Monthly Exterior Wipe it with water-dampened cloth As needed Interior Brush or vacuum As

316. Troubleshooting The following guide lists the most common problems that may be encountered when operating this bar code printer. If the printer

32 6.2 Print Quality Problem Possible Cause Recovery Procedure Check if interface cable is well connected to the interface connector. Re-connect ca

337. LED and Button Operation 7.1 LED LED Color Description Green/ Solid This illuminates that the power is on and the device is ready to use. Gr

34Gap/Black Mark Sensor Calibration 1.Turn off the power switch. 2. Hold on the button then turn on the power switch. 3 Release the button when LE

35Printer Initialization 1. Turn off the power switch. 2. Hold on the button then turn on the power switch. 3. Release the button when LED

36Skip AUTO.BAS 1. Turn off printer power. 2. Press the FEED button and then turn on power. 3. Release the FEED button when LED becomes solid green

37Revise History Date Content Editor 9-14-08 Pre-production Release J. Nolan

2 Optional Configurations  Peel off module assembly.  Guillotine cutter Full cut: Paper thickness: 0.06~ 0.19mm, 500,000 cuts Partial cut: P

Document #120523 Rev-A Corporate Headquarters Manufacturing/Service 803 Camarillo Springs Road, Suite-D 5033 Sirona Drive, Sui

32.3 Printer Parts 2.3.1 Front View Fig.1 Top Front View 2.3.2 Rear View 3 Setup 3.1 Setting Up the Printer 1.

43. Connect the printer to the computer with the Centronics or USB cable. 4 Plug the DC power cord into the power jack at the rear of the printer, a

5Media Guide 2. Open the printer’s top cover by releasing the green levers located on each side of the printer and lifting the top cover. 3. Plac

63.3 Peel-Off Module Installation (Option) 1. Open the top cover. 2. Remove the 6 screws in the lower inner cover. 3. Turn over the printer. 4

75. Remove the screw at memory card cover. 6. Separate the top, inner, and the lower cover. 7. Thread the cable red connector through the inn